User’s Guide
Shop online at
omega.com
e-mail: [email protected]
For latest product manuals:
omegamanual.info
KH, KHR, KHLV SERIES
®
Kapton Flexible Heaters
KH, KHR, KHLV SERIES
®
Kapton Flexible Heaters
INSTALLATION AND OPERATION
CAUTION
Use a method of temperature control (e.g., thermostat,
thermocouple and temperature controller, or variable
voltage transformer) to prevent heaters from exceeding
maximum operating temperature ratings. Place temperature
sensor close enough to the heater to sense heater
temperature.
1. DO NOT immerse heaters in liquids.
2. DO NOT operate heaters at a voltage higher than the specified or
rated voltage.
3. DO NOT cut, punch holes in or otherwise mishandle heaters.
4. AVOID exposing heaters to chemicals, acids, alkalies. oils fluids or
other substances that could ignite or cause damage to the heaters.
5. DO NOT insulate heaters unless adequate measures are taken to
control heater temperature.
6. DO NOT leave heaters operating unattended unless adequate
controls are installed to insure safety.
7. Heaters can be bent around curved surfaces; however, DO NOT
exceed minimum banding radius.
8. Exercise care in attaching heaters to flat or curved surfaces. Heaters
can be attached by mechanical clamping, by using factory applied
pressure sensitive adhesive (PSA), or with a thin layer of conductive
epoxy. Make sure that the entire heater is in contact with the surface
with no air pockets trapped underneath. This is especially important
for high watt density heaters, i.e. heaters with a watt density of 10
watts/square inch, to prevent heater failure. DO NOT overlap
heaters.
9. Heaters must be attached to an appropriate heat sink and should
NOT be mounted free-standing In air.
10. Make sure heaters are installed and used by qualified personnel.
DO NOT attempt to repair damaged heaters.
Servicing Europe:
Benelux:
Postbus 8034, 1180 LA Amstelveen, The Netherlands
Tel: +31 (0)20 3472121
FAX: +31 (0)20 6434643
OMEGAnet® Online Service
omega.com
Internet e-mail
Toll Free in Benelux: 0800 0993344
e-mail: [email protected]
Czech
Republic:
Frystatska 184, 733 01 Karviná, Czech Republic
Servicing North America:
One Omega Drive, Box 4047
Tel: +420 (0)59 6311899
Toll Free: 0800-1-66342
FAX: +420 (0)59 6311114
e-mail: [email protected]
U.S.A.:
ISO 9001 Certified Stamford, CT 06907-0047
France:
11, rue Jacques Cartier, 78280 Guyancourt, France
Tel: +33 (0)1 61 37 2900 FAX: +33 (0)1 30 57 5427
Toll Free in France: 0800 466 342
e-mail: [email protected]
Tel: (203) 359-1660
FAX: (203) 359-7700
e-mail: [email protected]
Canada:
976 Bergar
Laval (Quebec) H7L 5A1, Canada
Tel: (514) 856-6928
Germany/
Austria:
Daimlerstrasse 26, D-75392 Deckenpfronn, Germany
FAX: (514) 856-6886
Tel: +49 (0)7056 9398-0
FAX: +49 (0)7056 9398-29
e-mail: [email protected]
Toll Free in Germany: 0800 639 7678
e-mail: [email protected]
For immediate technical or application assistance:
®
United
Kingdom:
ISO 9002 Certified M44 5BD United Kingdom
One Omega Drive, River Bend Technology Centre
Northbank, Irlam, Manchester
U.S.A. and
Sales Service: 1-800-826-6342 / 1-800-TC-OMEGA
Customer Service: 1-800-622-2378 / 1-800-622-BEST
®
Canada:
®
Engineering Service: 1-800-872-9436 / 1-800-USA-WHEN
TELEX: 996404 EASYLINK: 62968934 CABLE: OMEGA
Tel: +44 (0)161 777 6611
FAX: +44 (0)161 777 6622
Toll Free in United Kingdom: 0800-488-488
e-mail: [email protected]
Mexico:
FAX: (001) 203-359-7807
It is the policy of OMEGA Engineering, Inc. to comply with all worldwide safety and EMC/EMI regulations that apply. OMEGA is constantly pursuing
certification of its products to the European New Approach Directives. OMEGA will add the CE mark to every appropriate device upon certification.
The information contained in this document is believed to be correct, but OMEGA accepts no liability for any errors it contains, and reserves the
right to alter specifications without notice.
WARNING: These products are not designed for use in, and should not be used for, human applications.
WARRANTY/DISCLAIMER
OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a period of 13 months from
date of purchase. OMEGA’s WARRANTY adds an additional one (1) month grace period to the normal one (1) year product
warranty to cover handling and shipping time. This ensures that OMEGA’s customers receive maximum coverage on each
product.
If the unit malfunctions, it must be returned to the factory for evaluation. OMEGA’s Customer Service Department will issue an
Authorized Return (AR) number immediately upon phone or written request. Upon examination by OMEGA, if the unit is found to be
defective, it will be repaired or replaced at no charge. OMEGA’s WARRANTY does not apply to defects resulting from any action of the
purchaser, including but not limited to mishandling, improper interfacing, operation outside of design limits, improper repair, or
unauthorized modification. This WARRANTY is VOID if the unit shows evidence of having been tampered with or shows evidence of
having been damaged as a result of excessive corrosion; or current, heat, moisture or vibration; improper specification;
misapplication; misuse or other operating conditions outside of OMEGA’s control. Components in which wear is not warranted,
include but are not limited to contact points, fuses, and triacs.
OMEGA is pleased to offer suggestions on the use of its various products. However, OMEGA neither assumes responsibility
for any omissions or errors nor assumes liability for any damages that result from the use of its products in accordance with
information provided by OMEGA, either verbal or written. OMEGA warrants only that the parts manufactured by the
company will be as specified and free of defects. OMEGA MAKES NO OTHER WARRANTIES OR REPRESENTATIONS OF ANY
KIND WHATSOEVER, EXPRESSED OR IMPLIED, EXCEPT THAT OF TITLE, AND ALL IMPLIED WARRANTIES INCLUDING ANY
WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. LIMITATION
OF LIABILITY: The remedies of purchaser set forth herein are exclusive, and the total liability of OMEGA with respect to this
order, whether based on contract, warranty, negligence, indemnification, strict liability or otherwise, shall not exceed the
purchase price of the component upon which liability is based. In no event shall OMEGA be liable for consequential,
incidental or special damages.
CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor shall it be used: (1) as a “Basic Component” under 10 CFR
21 (NRC), used in or with any nuclear installation or activity; or (2) in medical applications or used on humans. Should any Product(s)
be used in or with any nuclear installation or activity, medical application, used on humans, or misused in any way, OMEGA assumes
no responsibility as set forth in our basic WARRANTY/DISCLAIMER language, and, additionally, purchaser will indemnify OMEGA and
hold OMEGA harmless from any liability or damage whatsoever arising out of the use of the Product(s) in such a manner.
RETURN REQUESTS / INQUIRIES
Direct all warranty and repair requests/inquiries to the OMEGA Customer Service Department. BEFORE RETURNING ANY
PRODUCT(S) TO OMEGA, PURCHASER MUST OBTAIN AN AUTHORIZED RETURN (AR) NUMBER FROM OMEGA’S CUSTOMER
SERVICE DEPARTMENT (IN ORDER TO AVOID PROCESSING DELAYS). The assigned AR number should then be marked on the
outside of the return package and on any correspondence.
The purchaser is responsible for shipping charges, freight, insurance and proper packaging to prevent breakage in transit.
FOR WARRANTY RETURNS, please have the following informa-
tion available BEFORE contacting OMEGA:
1. Purchase Order number under which the product was
PURCHASED,
2. Model and serial number of the product under warranty, and
FOR NON-WARRANTY REPAIRS, consult OMEGA for cur-
rent repair charges. Have the following information avail-
able BEFORE contacting OMEGA:
1. Purchase Order number to cover the COST of the repair,
2. Model and serial number of the product, and
3. Repair instructions and/or specific problems relative to the
product.
3. Repair instructions and/or specific problems relative to
the product.
OMEGA’s policy is to make running changes, not model changes, whenever an improvement is possible. This affords our customers the latest in
technology and engineering.
OMEGA is a registered trademark of OMEGA ENGINEERING, INC.
© Copyright 2005 OMEGA ENGINEERING, INC. All rights reserved. This document may not be copied, photocopied, reproduced, translated, or
reduced to any electronic medium or machine-readable form, in whole or in part, without the prior written consent of OMEGA ENGINEERING, INC.
M1249/0205
|